Fishing Tools in Oil and Gas: The Tool Families, the Companies That Run Them, and the Shop Behind the Fishing String
A fish is anything left in a well that stops the next job, and getting it out is a sequence of catch, impact and cutting tools that each start and end on a bench in the fishing company’s shop.
Fishing tools in oil and gas are the catch, impact and cutting tools run to recover a fish: anything left in the wellbore that stops the next operation, such as parted drill pipe, a dropped tool or a lost bit cone. An overshot or spear grips it, jars hammer it free, mills and washpipe cut around it. Each is a threaded assembly, serviced on a bench between jobs.
At a glance
| What a fish is | Any object in the hole that should not be there: a parted drill string, pipe stuck by differential pressure or a collapsed hole, a twisted-off tool, junk such as bit cones or hand tools, or a logging tool and its cable |
| What fishing is | Any operation run to recover the fish, or to cut it, mill it or wash over it so that the well can go on; if that fails, the alternative is to plug back and sidetrack around it |
| The main tools | Catch tools (overshot, spear), impact tools (fishing jar, bumper sub, accelerator), diagnosis tools (impression block, free-point tool), parting and cutting tools (back-off shot, junk mill, pilot mill, washover shoe, pipe cutters), junk tools (junk basket, magnet, boot basket) |
| Who does it | A fishing tool company with a tool supervisor on the rig and a tool shop at its base; the operator decides each day whether to keep fishing or to sidetrack |
| The economics | Fishing is paid for by the day, in rig time, tool rental and service; the decision to stop is reached when the cost of continuing approaches the cost of sidetracking and the value of the fish |
| The threaded part | Most fishing tools and work-string joints carry rotary shouldered or tubing connections; the tools’ internal connections are made up, tested and recorded in the fishing company’s shop before the job, and the whole string is broken out again after it |
| Decision this page supports | Understanding what a fishing job involves, which tools do what, when the sidetrack decision comes, and what the tool shop behind a fishing company has to be equipped to do |

What a fish is, and why it happens
A well is drilled and completed by running long strings of threaded steel into a hole that is a few inches wider than they are, through rock that can cave, swell, or hold the pipe against its wall. The drill string twists off at a fatigued connection and leaves the bottom hole assembly at the bottom; the pipe stops moving because the hole collapsed around it or the mud pressed it against a permeable wall until the friction beat the rig’s pull; a bit cone comes off, a wrench drops through the rotary table, or a logging tool wedges in a ledge and its cable parts. Each of these is a fish, the industry’s word for anything in the hole that prevents the next operation, and the glossary defines fishing as the application of tools, equipment and techniques for removing it (SLB Energy Glossary: fishing).
The reasons sort into three groups. Parted strings fail at connections more than anywhere else: fatigue cracks at the tool joint, damage from tong dies, corrosion, and connections made up to the wrong torque, which either shoulder loosely and wobble to failure or are overstressed in the pin. Stuck pipe comes from differential sticking against a permeable formation, from mechanical sticking in a collapsing or undergauge hole, from key seats worn by the pipe in a dogleg, and from cement that set while the string was still in it. Junk is everything else: cones and bearings, reamer and hole opener parts, hand tools, and the wireline tools that could not be pulled (Drilling Manual: Fishing in Drilling Oil and Gas Operations). The connection failures in that list are the only part of it a tool shop can prevent.
Before the tools: the fish profile
A fishing job begins with a profile sheet: the depth of the top of the fish from the tally, its outside and inside diameters and connection type, what the top looks like after the failure, the hole and casing sizes above it, the mud, the temperature and pressure at depth, and what has already been tried. One recent industry guide puts that into a twelve-field sheet handed from the rig to the fishing company before any tool is chosen (Welong: Fishing Operation in Drilling, a Job Planning Guide). Two fields decide the first tool: a clean top takes an overshot on the outside, a damaged top or a tight clearance takes a spear on the inside, and an unknown top takes an impression block first. For a string that is still connected, a free-point tool run on wireline finds where it is stuck (SLB Energy Glossary: free-point indicator), a back-off shot is placed at the chosen connection above that point, and the free pipe is unscrewed and recovered; a looser joint higher up letting go first is a known risk of the method, and one reason the make-up record of a drill string is worth keeping. The five decisions that run the job from that sheet to the sidetrack call are set out step by step in downhole tool recovery; this page is about the tools themselves and the shop behind them.

Fishing tools in oil and gas: the string that goes in the hole
The string run to recover a fish is a bottom hole assembly built for pulling rather than drilling. From the catch tool upward: the overshot or spear, a bumper sub that lets the string deliver a downward blow and gives the catch some travel, a fishing jar that delivers the upward blow, tripping at a preset load if it is mechanical or after a timed delay at the applied pull if it is hydraulic, drill collars whose mass is what makes the blow count, an accelerator above the collars, a spring or gas-charged tool that isolates the jar from the stretch and friction of the drill pipe and gives the collar mass a sharp acceleration when the jar trips (SLB Energy Glossary: accelerator), and drill pipe to surface. Often a safety joint sits above the catch tool so that the string can be unscrewed and recovered if the fish refuses to move.
Most jobs start with an overshot. It is a bowl with a tapered inside, a grapple that slides into the bowl and grips the fish, a control that stops the grapple turning, and a guide at the bottom that steers the tool over the top of the fish. Set down and rotated onto the fish, the grapple expands; pulled up, the taper drives the grapple into the fish and the grip tightens with the load (SLB Energy Glossary: overshot). It can be released by jarring down and turning, which is what lets the string come home without the fish if it must. A spear works the same way inside the bore, with a grapple that expands outward against the inside of the fish.
| Tool | What it does | What the shop does to it between jobs |
|---|---|---|
| Overshot and spear | Catch the fish by its outside or inside and hold it under pull and jarring | Break out bowl, grapple, control and guide; inspect and replace the grapple; make up to the maker’s torque; record by serial |
| Fishing jar | Delivers an upward impact to free a stuck fish when the jar trips: at a preset load for a mechanical jar, after a timed delay for a hydraulic one | Strip, inspect seals and mandrel, re-make the body connections, then prove the trip load or the delay on a jar tester before it is rented again |
| Bumper sub | Delivers a downward impact and gives the catch free travel | Splines and seals inspected after every job before the body is re-made |
| Accelerator | Isolates the jar from drill-pipe stretch and friction so the collar mass hits hard | Spring or gas charge checked and reset, then the body re-made and pulled to confirm its stroke |
| Junk mill, pilot mill, washover shoe | Mill the top of the fish flat, mill around a stuck tool, or cut the formation away around the fish with washpipe | Re-dress the cutting faces, inspect the body and connection, make up to the washpipe or sub |
| Junk basket, magnet, boot basket | Recover cones, bearings, hand tools and wireline that cannot be gripped | Cleaned and inspected; catchers and magnets replaced as they wear |
| Safety joint and releasing tools | Let the string back off above the catch and leave the tool if the fish will not come | Inspect the release mechanism, make up to its set torque, which is lower than the string’s, and record it |
Running the job, and when to stop
The job itself follows a short sequence, described in full on the recovery page: condition the hole and spot a viscous pill above the fish, run the string to within a few feet of it and circulate the top clean, latch with the catch tool, test the pull, and if the fish holds, work the jar in cycles while the weight indicator is watched for any gain. A long stuck string may instead be freed by washover, drilling over it with washpipe and a rotary shoe to cut the formation or cement away before it is caught again (SLB Energy Glossary: washover), and junk is milled to pieces small enough for a basket or lifted on a magnet.
Each run is a decision point. The planning guide is blunt that there is no universal time or cost cut-off; each attempt either adds evidence about the fish or it does not, and the operator weighs what was learned against the day rate. The older rule of thumb, still quoted in the Drilling Manual guide linked above and one rule among several, is that fishing should be abandoned when its cost approaches half the cost of sidetracking and re-drilling, with the value of the fish counted on the fishing side. Sooner or later the conversation turns to the sidetrack: a cement plug above the fish, a new hole kicked off beside it, and the fish left where it is. If the sidetrack is not worth it either, the well is plugged, the route described in plug and abandonment.
Where the fishing tools are made up
Lay the fishing string out and count the connections: overshot guide to bowl, bowl to top sub, top sub to safety joint, safety joint to bumper sub, bumper sub to jar, jar to collars, collars to accelerator, accelerator to drill pipe, and inside the jar, the bumper sub and the accelerator, the internal body connections that hold the mechanism together. The joints between the tools are made up on the rig floor with the rig tongs as the string is built, and the overshot is often dressed on location with the grapple, control and guide that suit the fish. What the shop owns is the inside of the tools: the body connections of the jar, the bumper sub and the accelerator, made up before the tools left the base, and the break-out of all of it after the job.
A fishing company’s tool shop is a service shop like the ones described in downhole tools, with two things that make its work harder than plain collars. Its tools are mechanisms: jars with mandrels, seals and trip settings, accelerators with springs or charged chambers, overshots with grapples that must slide freely in their bowls. And its tools come back from the hole having been jarred, pulled, milled on and rotated, so the break-out after a job is the heavy end of the shop’s work, and it has to be done without crushing a body that has a mandrel inside it. The horizontal bench that does that work is a hydraulic bucking unit with jaws chosen for tool bodies, supports for long assemblies, break-out capacity sized from what returns from the hole rather than from the make-up tables, and a torque trace that is filed against the tool’s serial number. Why the break-out side sizes the machine is set out in what is breakout force, and shops with a high volume of returning tools keep a breakout unit beside the bench for that half of the cycle.
The jar needs one more step. A fishing jar is rented on the promise that it will fire as built, at a set load for a mechanical jar or after a set delay at the applied pull for a hydraulic one, and the only way to know is to pull it on a tester and watch it fire. Galip builds the drilling jar tester that does that, and the procedure for a test, from the pull to the record, is described in the drilling jar testing procedure, with the inspection points in the drilling jar maintenance and inspection checklist. How a drilling jar and a fishing jar fire differently, and how the trip load is proved, is the subject of the drilling jar trip load guide. For a fishing company the bench and the tester sit in the same bay: the jar is broken out on one, serviced, made up on it again, then pulled on the other, and both records go in the file with the tool.
Preventing the fish
The cheapest fishing job is the one that never starts, and most of the prevention lives in the same shops. Drill pipe is inspected between wells and connections that are worn, cracked or washed are cut off and re-made. Collars and subs are gauged and their shoulders checked. Each connection in the bottom hole assembly is made up to its table in the yard with a record, since a wrong torque is the commonest way a string parts. The components and where each is made up are set out in drill string components. On the rig, the prevention is watching: drilling torque, drag on connections, the sweeps before a trip, and the rule the manuals give for any bottom hole assembly component whose condition is in doubt, which is to leave it out.
Where fishing sits in the industry
Fishing is a service, bought by the day from fishing tool companies and from the fishing divisions of the larger service companies, and it is called out by drilling contractors and operators in the drilling, completion and workover phases alike. A workover rig fishes for parted tubing and failed pumps as often as a drilling rig fishes for drill pipe; the jobs on that side are described in workover rig operations. Coiled tubing units carry small fishing tools into live wells. Wherever the fish is, the tool shop behind the job is the same, and it belongs to the upstream oil and gas sector’s service layer, the companies that own the tools and rent them with a supervisor.
When another page is the better start
A reader whose question is the jar itself, how it trips, how it is tested and what the test report shows, should go to the jar tester guide and the testing procedure. A reader planning a specific fishing job should start on the downhole tool recovery page, which walks through the five decisions, and then needs the fishing company’s supervisor and the tool catalogue, with dimensions. A reader whose question is why connections part should read the drill string components page and the pages on make-up torque. A fishing company equipping its shop, which already knows its tool range and connection types, should go to the bucking unit product page and ask about jaw sets for tool bodies, break-out capacity, long-tool supports, and whether a jar tester and a bench can share a bay.
One limit: jar trip loads, overshot grapple sizes and make-up torques belong to the tool makers’ manuals, and this page stops at the job and where the tools are made up.
Frequently asked questions
What are fishing services in oil and gas?
Oil well fishing is the recovery of anything left in a wellbore that stops the next operation: parted or stuck drill pipe, a dropped tool, bit cones, a logging tool and its cable. Fishing services are the companies that own the catch, impact and cutting tools, send a supervisor to the rig with them, and take them back to a tool shop afterwards; the operator decides each day whether to keep fishing or to sidetrack.
What are the main fishing tools in oil and gas?
Fishing tools fall into five families. Catch tools grip the fish: an overshot on its outside, a spear on its inside. Impact tools free it: fishing jar, bumper sub and accelerator, hammering with the collar mass. Diagnosis tools read it: impression block and free-point tool. Parting and cutting tools get past it: back-off shot, junk mill, washover shoe and pipe cutters. Junk tools lift what cannot be gripped: junk basket, magnet and boot basket.
What causes a fish in a well?
A fish is a parted string, stuck pipe, or junk. A string parts at a connection weakened by fatigue, tong damage, corrosion or wrong make-up torque. Pipe sticks by differential pressure against a permeable formation, in a collapsing or undergauge hole, in a key seat worn in a dogleg, or in cement that set around it. Junk is bit cones, reamer parts, dropped hand tools and wireline tools that could not be pulled.
When should a fishing operation be stopped?
A fishing operation should stop when the cost of continuing approaches the cost of the alternative. The older rule of thumb is to stop when fishing costs reach about half the cost of sidetracking and re-drilling, with the value of the fish on the fishing side. Current planning guidance adds that there is no universal cut-off: each run is judged by what it taught about the fish, against the rig and tool day rate.
Where are fishing tools made up and serviced?
Fishing tools are made up and serviced in the fishing company’s tool shop. After each job they are broken out, stripped, inspected, redressed, made up to the maker’s torque on a horizontal bucking unit and recorded by serial number, and jars are pulled on a jar tester. The rig floor makes up the joints between the assembled tools and the drill pipe; the shop owns what is inside the tools.
Send the tool list with the enquiry
A fishing tool shop is quoted from its fleet. The useful set for a bucking unit or jar tester quotation is: the range of tool outside diameters and lengths, the connection types, the heaviest body to be clamped and whether it carries an internal mandrel, the highest make-up torque in the makers’ manuals and the highest break-out expected on tools returned from the hole, the jar sizes and their maximum trip loads, the record format required by customers, the site power supply and a sketch of the service bay. The Galip team quotes from that list and will say where a tester belongs beside the bench.
The fishing tools checklist
- Fill the fish profile before choosing a tool: depth of the top, diameters, connection, condition of the top, hole and casing sizes, fluid, what was tried; the decision sequence is on the downhole tool recovery page.
- Choose the catch by the top: overshot for a clean outside, spear for a damaged top or tight clearance, impression block when the top is unknown.
- For a stuck string, find the free point, back off above it, recover the free pipe, then fish or wash over the rest.
- Build the string with a bumper sub below the jar and an accelerator above the collars, and a safety joint above the catch.
- Condition the hole and spot a pill above the fish before tripping the tools.
- Treat each run as a decision; weigh what it taught against the day rate and the cost of a sidetrack.
- Break out, inspect, make up and record each tool in the shop after the job; pull each jar on a tester before it goes out again.
- Prevent the next fish in the same shop: inspect the drill string, re-make damaged connections, make up the bottom hole assembly joints to their tables with a record.
Expert Consultation
Need more information on optimizing your equipment performance? Our engineering team is available for technical consultations.
Request a Quote
Tell us about your requirements and our engineering team will prepare a detailed proposal with specifications, pricing, and delivery timeline.
